Many utility and mine stations spend more hours at low load than their designers expected. This guide explains what happens inside an HFO engine at low load, how operators can dispatch units to avoid it, when to change over to distillate fuel, and which signals warn that low load running is starting to cost money.
What counts as low load
Every engine maker publishes its own limits, but as a working rule an HFO engine running continuously below about 30 to 40 percent of its rated output is in the low load zone. Many makers also set a time limit, for example a maximum number of hours at very low load before the engine must be run up to a higher output for a period.
The limits are tighter on heavy fuel than on distillate, because heavy fuel needs high combustion temperatures to burn completely. Check the operating manual for each engine type in the station, since a mixed fleet can have different thresholds for each model.
What happens inside the engine
At low load the cylinder pressure and temperature fall, the turbocharger delivers less air and fuel atomisation becomes poorer. Heavy fuel droplets burn incompletely and leave carbon on the piston crown, the exhaust valves and the nozzle tips. Unburnt fuel and soot pass into the exhaust system and build up in the turbine side of the turbocharger and in any exhaust gas boiler.
Some of the fuel and soot also find their way past the rings into the lube oil, raising its viscosity and insoluble content. Meanwhile liner wall temperatures drop, and sulphur in the fuel can condense as sulphuric acid on the cooler surfaces. This cold corrosion wears liners and rings far faster than normal operation.
Why stations end up at low load
The common causes are spinning reserve rules that keep extra units connected, night-time load valleys on isolated grids, a mine load that never grew as forecast, and solar plant added beside the engines that pushes them down during the day. Stations sized with a few very large engines are especially exposed, because there is no small unit to carry the valley.
Our page on running a station for fuel economy covers the efficiency side of this question; the mechanical side matters just as much, because deposits and liner wear raise maintenance costs long after the fuel saving or loss has been counted.
Unit commitment: fewer engines, harder working
Take a station with six 8 MW engines and a night load of 18 MW. Running all six shares the load at 37.5 percent each, inside the low load zone. Running three engines puts each at 75 percent, close to the efficient point, and a fourth unit at moderate load provides reserve if needed.
The fuel effect alone is significant. If specific consumption is about 200 grams per kilowatt-hour at 75 percent load and about 225 grams at 37.5 percent, the 18 MW night load costs roughly 450 kilograms of fuel an hour more when spread across six engines. Over an eight-hour night that is more than 3.5 tonnes, before any extra maintenance is counted.
Changing over to distillate fuel
When an HFO engine must run at low load for a long period, such as during a planned grid valley or standby duty, many operators change over to marine diesel or light fuel oil. Distillate burns cleanly at low temperatures and avoids most of the deposit and acid problems.
The changeover itself must be controlled. Fuel temperature falls from around 130 degrees Celsius on heavy fuel to near ambient on distillate, and a fast change can cause injection pump plungers to stick through thermal shock. Follow the maker’s limit on the rate of temperature change, and make sure the booster module and fuel coolers are set up for the lighter fuel.
Load-up runs and cleaning cycles
Most makers require a periodic load-up after extended low load running: the engine is taken to a high output, often above 70 percent, for a set time to burn off deposits and clear the turbocharger and exhaust path. The increase in load should be gradual, because deposits loosening all at once can cause turbocharger surging or exhaust temperature spikes.
Turbocharger water washing on the turbine and compressor sides, at the intervals the maker sets, helps restore performance. Record each load-up and wash in the maintenance system so the operating team can see whether low load hours are being managed or simply accumulating.
Temperature and lubrication settings
Some engines allow adjustments that ease low load running: raising jacket water and charge air temperatures to keep liner walls warm, switching charge air coolers to a low load mode, and adjusting cylinder lubrication where a separate system is fitted. Only make these changes within the maker’s guidance, and return to normal settings when load rises.
Lube oil base number deserves attention too. An oil chosen for heavy fuel neutralises acid, but if acid production rises at low load, the base number can fall faster than planned. Our article on HFO station auxiliary systems describes the oil treatment equipment that supports these settings.
Signals to monitor
The early warnings are an increasing spread of exhaust temperatures between cylinders, rising turbocharger speed for the same load, falling charge air pressure, visible smoke on load changes and higher lube oil consumption. Oil analysis showing fuel dilution, rising insolubles or a falling base number confirms the trend.
Borescope inspections of liners at scheduled stops will show lacquering or corrosion marks before they become expensive. A station that tracks these signals by engine can decide on facts whether to change its dispatch rules, rather than discovering the damage at the next overhaul. Our station operations and maintenance team builds these checks into routine reporting.
Design and operating rules that help
At the design stage, a mix of unit sizes, or a battery system that carries spinning reserve, lets the station follow low loads without dragging large engines down. Where solar is part of the plan, size the engine fleet so that the remaining daytime load still keeps running units above their low load limit.
In operation, write the rules down: the minimum load per engine on each fuel, the maximum hours at low load before a load-up, the changeover procedure, and the reserve policy. Clear written rules let shift operators make consistent decisions at three in the morning, which is when low load running usually happens.
About the authors
This guide comes from the USP&E station operations engineers and engine specialists who run HFO and diesel power stations and set their dispatch rules. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. For the broader engine choice, see our comparison of turbines and reciprocating engines.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
Low load operation questions
What is the minimum load for an HFO engine?
It depends on the maker, but continuous running below about 30 to 40 percent of rated output is usually treated as low load, with time limits set in the operating manual.
Why is low load bad for HFO engines?
Combustion temperatures fall, heavy fuel burns incompletely and leaves carbon deposits, lube oil is contaminated, and sulphuric acid can condense on cooler liner walls.
Should an HFO engine change to diesel at low load?
For long periods at low load many operators change to distillate, which burns cleanly when cool. The temperature change must follow the maker’s rate limit.
What is a load-up run?
A planned period at high output after extended low load running, used to burn off deposits and clear the turbocharger and exhaust system.
How can a station avoid running engines at low load?
Run fewer engines at higher output, mix unit sizes, or use battery storage for spinning reserve so large engines are not held at low output.
Which signs show low load damage?
Rising exhaust temperature spread, higher turbocharger speed, smoke on load changes, more lube oil use and oil analysis showing fuel dilution or falling base number.
Review your station dispatch rules
Send us your load profile, engine list and current dispatch practice, and our engineers will help you set low load limits, changeover steps and reserve rules for your station.
If a document set is easier than a conversation, send it to info@uspeglobal.com or upload a summary through the station engineering enquiry form; to talk it over, dial +27 10 822 2324. Medium-speed engines and generating sets are listed in our equipment inventory.
