Neutral Earthing for Diesel Power Stations | USP&E

Diesel Power Station

Generator Neutral Earthing for Multi-Engine Diesel Power Stations

Every generator in a power station has a star point, and what you connect that point to decides how violent an earth fault will be. Leave it solid and a winding fault can pass thousands of amperes and burn the stator core beyond repair. Leave it floating and an insulation fault can raise the other phases to line voltage with no clear trip signal.

Most medium-voltage diesel and HFO stations take the middle route and earth the neutral through a resistor. This article explains why, how the earth-fault current is chosen, and the layout choices that matter once several engines run in parallel.

What the neutral does in a fault

When a phase touches earth inside a generator, current flows through the fault and back through whatever impedance sits between the star point and ground. A low impedance gives a large current that is easy to detect but destructive, while a high impedance limits damage but makes detection harder.

The earthing method is therefore a design choice that sets fault energy, protection sensitivity and the voltage stress on healthy phases. It deserves study at the same stage as the single-line diagram, not as a late detail from the switchgear vendor.

Solid, resistance and unearthed schemes compared

Solid earthing is common at low voltage, where fault current can be tolerated and is useful for tripping breakers fast. At medium voltage it exposes machines to heavy damage, so stations at 6.6 kV and above rarely use it for the generator itself.

Resistance earthing limits the earth-fault current to a chosen value, often a few hundred amperes or less, and still allows a relay to see the fault clearly. Unearthed systems give the lowest fault current, but they stress insulation during arcing faults and can sit on a first fault unnoticed, which is why they are not a good fit for a power station feeding an industrial load.

Choosing the earth-fault current

The target current is a trade-off. It must be high enough for the earth-fault relay to operate over most of the stator winding, because a fault close to the neutral end produces little voltage and little current. It must be low enough to keep iron damage minor during the time the protection takes to clear.

Designers usually start from the relay’s sensitivity and the machine maker’s stated tolerance, then size the resistor value and its short-time rating. The resistor must withstand the full fault for the protection trip time plus margin, which is why a continuously rated unit is not always necessary but a correct short-time rating is.

One resistor per engine or one for the station

With several sets in parallel, each generator can have its own neutral resistor, or one common resistor can be switched in for the running set or sets. A resistor per set keeps the philosophy simple and each machine protected on its own, but several resistors in parallel multiply the fault current when many sets run.

A common scheme uses a single resistor on the bus-side transformer and isolates generator neutrals when not needed. The choice interacts with the layout described in our post on paralleling multi-MW diesel plants, because breaker logic decides which neutrals are connected at any moment.

Circulating currents and protection settings

When generators run in parallel with their neutrals tied together, third-harmonic currents can circulate between machines with differing winding pitch or load. These currents heat windings and can look like a fault to a poorly set relay.

Stator earth-fault protection normally combines a neutral current relay with a residual voltage element, and is set to ignore harmonics while remaining sensitive to the fundamental. A dynamic study across all running combinations, including one engine alone, confirms that the settings work in every operating mode. Our wider guide to the diesel station engineering and EPC scope shows where protection design sits in project delivery.

A worked sizing idea

To see how the numbers behave, consider a 6.6 kV station where each generator can contribute a bolted earth-fault current of several kiloamperes if solidly earthed. A resistor that limits the current to a few hundred amperes cuts the energy released in the fault by a large factor, because fault energy scales with the square of the current and the clearing time.

That reduction is what protects the stator core. The same figure also sets the minimum resistor rating: the element must tolerate the limited current for the whole trip time of the backup protection, not only the primary relay, so designers check both times when selecting the resistor.

Finally, make sure the protection philosophy is written down. Operators who understand why the neutral is earthed through a resistor, and what the relay indications mean, respond faster and more safely when an alarm comes in at three in the morning.

Testing and upkeep

Neutral resistors are passive and easy to forget, yet they sit in a harsh environment of heat, vibration and dust. Commissioning should include a primary injection test that confirms the relay sees the intended current, and a resistance measurement of the element.

Maintenance should repeat that measurement at intervals, inspect connections for corrosion and check cable terminations. A resistor with an open element will not announce itself, but the earth-fault protection it supports will not work as designed.

About the authors

This guide comes from the USP&E electrical engineers who design protection and earthing for diesel and HFO power stations. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. For the mechanical and electrical balance around the engines, see our HFO power station EPC and O&M guide.

Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.

Neutral earthing questions

Why is the generator neutral earthed through a resistor?

A resistor limits earth-fault current to a level that protects the stator core, while still letting a relay detect the fault clearly.

Is solid earthing used on medium-voltage generators?

Rarely. The fault current can be large enough to damage the stator iron, so most medium-voltage stations use resistance earthing.

How is the earth-fault current value chosen?

It balances protection sensitivity, which needs enough current, against damage limits, which need low current. The machine maker’s data and relay settings guide the choice.

Can paralleled generators share one neutral resistor?

Yes. Many stations use one resistor for the bus or transformer and isolate the generator neutrals, but the scheme must work for every running combination.

What causes circulating third-harmonic currents?

They flow when generators with different winding designs run in parallel with their neutrals connected, and they can mimic an earth fault if relays are not set to ignore them.

How should a neutral earthing resistor be tested?

Measure the element resistance, inspect connections and run a primary injection test to confirm that protection sees the expected current.

Review your earthing design

Send your single-line diagram and generator data sheets, and our engineers will review the neutral earthing and earth-fault protection against the way the plant will really run.

If a document set is easier than a conversation, send it to info@uspeglobal.com or upload a summary through the earthing design review request; to talk it over, dial +27 10 822 2324. Medium-voltage and low-voltage sets for station projects are listed in our diesel generator inventory.


Where we operate

USA | AFRICA | UK | UAE | CHINA

USP&E United States

Colorado Springs Office: 1755 Telstar Dr, Suite 300

Knoxville Office: 800 S Gay St, Suite 700

USP&E South Africa

Johannesburg Office: 22 Kildoon Rd, Bryanston

Cape Town Office: 31 Brickfield Road, Woodstock

USP&E United Kingdom

London Office: 162-168 Regent Street

USP&E China

China Office: No. 1, Ningzhou Road, Wuxi

Call:+27 10 822 2324  |  E:info@uspeglobal.com

ISO Certifications
ISO9001ISO45001

Powering Possibility. Built for the Frontier.
Full-service EPC & O&M. Not a broker.

© 2026 USP&E · Diesel Power Station is part of USP&E