Noise Control for Diesel and HFO Power Stations | USP&E

Diesel Power Station

Noise Control for Diesel and HFO Power Stations

A utility or mine power station with eight or ten medium-speed engines is one of the loudest pieces of plant a community is likely to live near. Engines, turbochargers, exhaust stacks, radiator fans and transformers all add to the sound field, and at night, when background levels drop, a station that met its limits on paper can still produce complaints from a village a kilometre away.

Noise is far cheaper to design out than to fix after commissioning. This guide explains where the sound comes from, how levels from several engines add up, how boundary limits are usually framed, and which measures bring a diesel or HFO station within those limits.

Where the noise comes from

The engine itself radiates mechanical and combustion noise through its block and casing, typically well above 100 dB(A) at one metre inside the hall. The exhaust carries high-energy pulsating gas to atmosphere and is often the strongest source heard off site. Charge air intakes, radiator or cooler fans, ventilation louvres and step-up transformers make up most of the rest.

Each source has its own frequency character. Exhaust and engine noise contain a large low-frequency component, fans tend to be broadband, and transformers hum at twice the network frequency and its harmonics. Mitigation has to match the source, because a measure that works well on fan noise may do little for a low exhaust rumble.

Decibel arithmetic for several engines

Sound levels add on a logarithmic scale. Two equal sources together are 3 dB louder than one, four equal sources are 6 dB louder and ten equal sources are 10 dB louder. A station of ten identical engine stacks therefore produces about 10 dB more at the boundary than a single stack, provided the distances are similar.

Distance helps in the opposite direction. In open ground a point source falls by about 6 dB for every doubling of distance, so a level of 85 dB(A) at 25 metres drops to roughly 61 dB(A) at 400 metres before ground and air absorption are counted. These simple rules let engineers test a layout quickly before running a full noise model.

Limits at the boundary and at night

Most environmental permits set noise limits at the site boundary or at the nearest homes, with lower values at night. Many lenders and permitting authorities refer to international guidance that limits the increase above existing background levels as well as the absolute level, so a quiet rural site can be harder to satisfy than an industrial area.

Before design starts, a baseline survey should record day and night background levels at each receptor. The permitting process for engine stations normally asks for this survey together with a predicted noise contour, so both should be part of the early studies rather than an afterthought.

Layout and distance as the first measure

The cheapest decibel is the one gained through layout. Placing the engine hall so that its louvre walls and stacks face away from homes, putting tank farms and workshops between the hall and the boundary, and keeping radiator banks on the far side of the plant can save several decibels without any extra hardware.

Site selection matters even more. Our article on choosing a site for an engine station explains why distance to the nearest community is one of the screening criteria, alongside fuel access and grid connection.

The engine hall as an acoustic enclosure

A well-built hall with masonry or insulated steel walls can reduce radiated engine noise by 30 dB or more. The weak points are the openings: ventilation inlets and outlets, doors, cable and pipe penetrations, and roof vents. Each opening needs either an acoustic louvre or an attenuator sized for the airflow the hall requires.

Ventilation design and noise design pull in opposite directions, since more open area means more cooling and more noise escaping. The engineer balances them by using splitter attenuators in the air paths and by sealing every unused penetration. Doors should be acoustic grade and kept closed, which in practice means a procedure rather than a drawing.

Exhaust silencers and stacks

Exhaust silencers are sized by the attenuation needed and the back pressure the engine allows. Residential grade units achieve more attenuation than industrial grade units but are larger and heavier. A combination of reactive and absorptive sections is common, because reactive chambers deal with low-frequency pulses and absorptive packing handles higher frequencies.

Stack height spreads sound further as well as dispersing exhaust gas, so noise and air quality studies should share one model. On HFO stations, soot and heat can degrade absorptive packing over time, so silencer inspection belongs in the planned maintenance plan.

Radiators, fans and low-frequency noise

Large remote radiator banks can become the dominant source once engines and exhausts are treated. Lower fan tip speeds, more fan cells running slower, and variable speed control that reduces fan speed at night are effective measures. Acoustic barriers around radiator banks help where homes are close.

Low-frequency noise is the hardest to control because it passes through walls and travels far. It is felt as much as heard, and it is often the cause of complaints that standard A-weighted measurements do not explain. Specifying low-frequency limits in the design brief avoids that gap. The same applies when an older station is refurbished or re-engined, because new units and fans can change the noise character of the whole site.

Worker exposure inside the station

Noise control is also about the people who run the plant. Engine halls exceed safe exposure levels, so hearing protection zones, signage, a quiet control room and regular audiometric testing of staff are standard parts of a station safety plan.

Control room walls and windows should be specified for the hall level next to them. Our overview of station auxiliary systems covers the compressor and pump rooms, which are often overlooked noise sources near maintenance areas.

Measuring at commissioning and afterwards

Noise should be measured at the boundary and at receptors during performance testing, with the station at full load and at night. Results are compared with the permit and the predicted contour, and any shortfall is traced to its source with close-in measurements before changes are made.

After handover, a simple complaints log and periodic repeat surveys show whether ageing silencers, open doors or added plant are pushing levels up. Treating noise as an operating parameter, not just a permit condition, keeps the station on good terms with its neighbours for its whole life.

About the authors

This guide comes from the USP&E design engineers and site managers who build and operate diesel and HFO engine stations for utilities and mines. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Our power station engineering and construction work includes acoustic design from layout through commissioning.

Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.

Power station noise questions

What is the loudest part of a diesel power station?

Usually the exhaust, followed by the engines inside the hall, radiator fans and ventilation openings. Transformers add a tonal hum.

How much louder are ten engines than one?

About 10 dB louder at the same distance, because sound levels add on a logarithmic scale.

How far does power station noise travel?

In open ground, a point source falls by about 6 dB for each doubling of distance, before ground and air absorption are counted.

What noise limits apply to a power station?

Permits normally set day and night limits at the boundary or nearest homes, and many also limit the increase above background levels.

What is a residential grade exhaust silencer?

It is a silencer with higher attenuation than industrial grade units, used where homes are close, at the cost of more size and weight.

Why do neighbours complain when limits are met?

Often because of low-frequency noise, which standard A-weighted readings understate, or because night background levels are very low.

Plan a quieter station

Share your site plan, engine list and the distance to the nearest homes, and our engineers will outline the layout and attenuation needed to meet your noise limits.

If a document set is easier than a conversation, send it to info@uspeglobal.com or upload a summary through the power station design enquiry; to talk it over, dial +27 10 822 2324. Medium-speed and high-speed engine sets for station projects are shown in our diesel generating set listings.


Where we operate

USA | AFRICA | UK | UAE | CHINA

USP&E United States

Colorado Springs Office: 1755 Telstar Dr, Suite 300

Knoxville Office: 800 S Gay St, Suite 700

USP&E South Africa

Johannesburg Office: 22 Kildoon Rd, Bryanston

Cape Town Office: 31 Brickfield Road, Woodstock

USP&E United Kingdom

London Office: 162-168 Regent Street

USP&E China

China Office: No. 1, Ningzhou Road, Wuxi

Call:+27 10 822 2324  |  E:info@uspeglobal.com

ISO Certifications
ISO9001ISO45001

Powering Possibility. Built for the Frontier.
Full-service EPC & O&M. Not a broker.

© 2026 USP&E · Diesel Power Station is part of USP&E